STC-3018 LED Digital Microcompute Temperature Controller Thermoregulator Relay Heater Cooler 'C/'F Display Incubator Thermostat(STC-3018 DC12V)

Thermostat ControllersSTC-3018 LED Digital Microcomputer Temperature Controller Thermoregulator Relay Heating Cooling / Display Incubator Thermostat 10AHeating Cooling Relay Control AC110-220V DC12V 24VFeatures:1.Automatic conversion of refrigeration and heating mode2.Control mode of difference;Temperature display resolution 0.13.Multiple alarm mode selection4.Support temperature correction and support for power loss (the parameters of the sudden power failure are still valid5.Application range is like home temperature control, farm, various cold storage, greenhouse, aquarium, etcParameters:Item No.: STC-3018Display: / Modes: Heating and CoolingTemperature Measuring Range: -55 ° C ~ 120 ° C / -66°F~248°FMeasurement error: ±0.5° CAccuracy: ±0.1° CResolution: 0.1Storage temperature: -30 ° C ~ 75 ° CRelative Humidity: 20~85% (no condensation)Sensor error delay: 1 minutePower Supply: AC 110V~220V / DC12V/ DC24V<; 3WOutput Relay: 2 Relays: Cooling & Heating both 10A220VACNTC Probe Sensor 100cmDelay start and temperature calibration Function YESMounting Hole Size 71x29 mmDimension 75x345x85mm LxWxHMenu InstructionCodeFunctionSet RangeDefaultP0H/C (H: Heating, C: Cooling)(-55°C~120°C)/(-67°CF~248°F)0°C/68°FP1 Difference Value0.2-102 P2High temperature alarm(-55°C~120°C)/(-67°CF~248°F)80°C/176°FP3Low temperature alarm(-55°C~120°C)/(-67°CF~248°F)-55°C/-67°FP4Temperature correction-10~100 P5Delay start0-60 min0 P6°C/°F°C/°F°CPacking List:1x Temperature Controller + 1x NTC Probe Sensor + 1x Manual(Note: the spare sensor is not included)Panel IllustrationWork Signal Real time temperature / convert light Setting temperatureSet button Enter button Products model UP Key Down KeyKey operation instruction1 .The way to check parameter:Under normal working status shows the real-time temperature , press "set" key show the screen flash then press"up"key it displays temperature setting value; press"down"key it displays the difference value.2. The way to set parameter:Long Press" set" key for 5 seconds could to be the inner setting, press the " ent" button could be back when setting the temperature. Under normal working status , long press the "ent" button could on/off the devicesHeating and Cooling mode setting: Press and hold the"up"key button 3 seconds to start temperature flashing, use"up" or "down"key button to set start temperature valve.Press and hold the"up"key button 3 seconds to stop temperature flashing, use"up" or "down"key button to set stop temperature valve.<;Stop temperatureCooling Mode--Start temperature>Stop temperatureNormal mode: The red digital tube on the left shows the real-time temperature, the blue digital tube on the right shows the set temperature.Setting mode: The red digital tube on the left displays the setting mode, the blue digital tube on the right displays the setting contents.3. Restore system dataPress"up"and "down " and key together for 2 seconds could restore the systemOperation instruction P0: Working ModeIt need to set this mode when get the controller, setting for the "H" if need to be heating mode, if need to for the cooling mode to set for the "C"P1: Difference ValueThe difference value is when the thermostat reaches the setting temperature and stops, the difference when the thermostat required to work again.For example, if we set the heating mode, the temperature is 37-40 , then difference value will be 3 degreesP2: High temperature alarmWhen the temperature the setting valve, it will have the temperature alarm and stop workingP3: Low temperature alarmWhen the temperature below the setting valve, it will have the temperature alarm and stop workingP4: Temperature correctionIf tested temperature is different from the real-time temperature, you could use this function to correct the temperatue, final corrected temperature= tested temperature + temperature correction. For example , the temperature we tested is 25.6 but the real-time is 25.8, it could set P4 for 0.2, then the final corrected temperature is 25.6 + 0.2 =25.8 .P5: Delay startGenerally this function is used for compressor refrigeration. If the thermostat works for refrigerator and freezer, then it must set this value for it . Generally, the setting value is less than 3-6 minutes according to the size of the compressor back pressure.P6: °C/°F adjustableIf need to show the valve, it could adjust the unit for ,and the "/ convert light" will be on.If need to show the valve, it could adjust the unit for ,and the "/ convert light" will be off.If need to adjust faster and do not to P6, exit display and long press "up" key 3 seconds from °C to °F.Safety RegulationsDanger:1. Strictly distinguish the sensor down-lead, power wire and output relay interface from one another, and prohibit wrong connections or overloading the relay.2. Dangers: Prohibit connecting the wire terminals without electricity cut-off.Warning:Prohibit using the machine under the environment of over damp, high temp., strong electromagnetism interference orstrong corrosion.Notice:1.The power supply should conform to the voltage value indicated in the instruction.2.To avoid the interference, the sensor down-lead and power wire should be kept a distance.Wiring WaysIndependent power supply for loadSame power supply for load

• Thermostat Controllers
• STC-3018 LED Digital Microcompute Temperature Controller Thermoregulator Relay Heater Cooler 'C/'F Display Incubator Thermostat